Specific attention has been paid to obtain a linear response in the operating bandwidth, while handling ultra-low frequency transients with maximum control.

The 18” custom-designed woofer features a large motor structure with dual 3” voice-coils offering an extreme excursion, resulting in a 10 dB more excursion capability than a traditional (pro) 18” woofer. (not included in SPLpeak spec).

The direct-radiating transducer mounted in the internally-stiffened, sealed cabinet enables an in-room response below 10 Hz; The superb impulse response is a perfect match with the ultra-fast transient response of the Alcons pro-ribbon systems.

The ultra-slim enclosure design, with a depth of only 33cm / 13-in,  together with the M10 mounting points and the HV form factor provides for stacking, flying or wall- and ceiling-mounting in even the smallest of spaces.

For full system performance, the CRMS-LFE18sl is to be driven and controlled by the ALC amplified loudspeaker controller, to deliver the most accurate reproduction for even the lowest octaves, to bring the most realistic experience of speech, music and effects. The 4 ohms impedance caters for maximum amplifier efficiency.

The integrated factory presets in the drive processor of the ALC offer optimisation settings, as well as VHIR™ processing for perfect phase-matching with an Alcons pro-ribbon system.

The Signal Integrity Sensing™ pre-wiring ensures complete cable/connector compensation between the CRMS-LFE18sl and a SIS™-featured ALC, significantly increasing response accuracy and reducing both linear and non-linear distortion to an absolute minimum, regardless of cable length and system impedance.

Typical applications include LFE system for quality-conscious post-production facilities and mastering suites, high-end mix/screening rooms, recording studios and premium home theatres.

The post CRMS-LFE18sl mkII appeared first on Alcons Audio.

The front-loaded GB181 delivers highly accurate bass and sub-bass reproduction with maximum output and minimum distortion, achieved through the long excursion 18” transducer. This new-generation woofer features a large dual 4.5” voice-coil Neodymium motor, providing significantly extended excursion* while maintaining high sensitivity. The driver has been engineered with specific focus on minimizing distortion. *(excursion not included in SPLpeak specification.)

The Flow-Vent™ port design provides maximum breathing capacity, further increases overall output while reducing port compression.

The GB181 can be deployed in different ways: horizontally groundstacked, with a top cabinet (GR20 i.e.) on a pole in the M20 stand flange; Vertically groundstacked, even in multiples, with the GR20 stacked in the speaker-specific recess. Through the front-positioned extra NL4 connector, also a cardioid-stacked array is easily possible, providing maximum rearward LF rejection.

For optimal system performance, the GB181 is powered and controlled by the ALC amplified loudspeaker controller. Driven by the ALC, the GB181 offers maximum operational headroom, consistent audio quality, and long-term reliability.

The Signal Integrity Sensing™ pre-wiring provides complete cable and connector compensation between the GB181 and an SIS™ featured ALC; The resulting system damping factor of 10.000 offers further reduced distortion, regardless of cable length or system impedance.

The GB181 in road-version is finished in Durotect™ scratch-resistant coating; The system can be delivered in any RAL color finish, through the Architect Color Option™ program.

Two options are available: an installation version (“GB181i”) and a road version (“GB181”) with wheel dolly, 2 M20 threaded stand mount flanges and handles. The road version also features a recess for slide-free stacking of a GR20.

The post GB181 appeared first on Alcons Audio.

The CRMSQB can be stacked in multiples, making it an ideal building block to form bass arrays, for obtaining low frequency projection and throw control, drastically reducing the influence of the room acoustics. The controlled (cylindrical) projection of the CRMSQ can thus be extended down to the lower frequencies by enlarging the LF array length through adding extra CRMSQB modules.

The 8 ohms system impedance, makes for a very efficient amplifier channel loading, when assembling arrays of multiple units; I.e. a stack of three units, means an array of six 12” woofers driven by one amplifier channel.

The system delivers high output under lowest distortion possible. The new-generation 12” transducers feature a large, dual-3.5” voice-coil Neodymium motor, enabling a significantly-extended excursion, while maintaining a high sensitivity.

The 12” drivers are mounted in a direct-radiating, sealed chamber configuration; This caters for a super accurate performance with very smooth roll-off and is a perfect match with the sealed-configured CRMSQ system.

The integrated mounting hardware facilitates easy coupling with other CRMSQB. The shallow form-factor (either in width or depth) and Architect Color Option™ enables a stealth, unobtrusive integration In any application.

The CRMSQB is powered and controlled by the ALC amplified loudspeaker controller; Through the integrated processing and feedback, the ALC offers CRMSQB-specific drive processing with optimal response and long-term reliability. The integrated factory presets in the ALC drive processor offer gain, phase, array-length and filtering matching with all Alcons systems.

Through the Signal Integrity Sensing (SIS™) pre-wiring, the cable-length and connector resistance between the CRMSQB and SIS-featured ALC is dynamically compensated (system damping factor 10.000), further reducing distortion, while increasing response accuracy.

The CRMSQB is available as CRMSQB, with CRMSQ width-matching and as CRMSQBsl, with CRMSQ depth-matching, with a 25,4cm / 210-in. system depth

The post CRMSQBsl appeared first on Alcons Audio.

The CRMSQB can be stacked in multiples, making it an ideal building block to form bass arrays, for obtaining low frequency projection and throw control, drastically reducing the influence of the room acoustics. The controlled (cylindrical) projection of the CRMSQ can thus be extended down to the lower frequencies by enlarging the LF array length through adding extra CRMSQB modules.

The 8 ohms system impedance, makes for a very efficient amplifier channel loading, when assembling arrays of multiple units; I.e. a stack of three units, means an array of six 12” woofers driven by one amplifier channel.

The system delivers high output under lowest distortion possible. The new-generation 12” transducers feature a large, dual-3.5” voice-coil Neodymium motor, enabling a significantly-extended excursion, while maintaining a high sensitivity.

The 12” drivers are mounted in a direct-radiating, sealed chamber configuration; This caters for a super accurate performance with very smooth roll-off and is a perfect match with the sealed-configured CRMSQ system.

The integrated mounting hardware facilitates easy coupling with other CRMSQB. The shallow form-factor (either in width or depth) and Architect Color Option™ enables a stealth, unobtrusive integration In any application.

The CRMSQB is powered and controlled by the ALC amplified loudspeaker controller; Through the integrated processing and feedback, the ALC offers CRMSQB-specific drive processing with optimal response and long-term reliability. The integrated factory presets in the ALC drive processor offer gain, phase, array-length and filtering matching with all Alcons systems.

Through the Signal Integrity Sensing (SIS™) pre-wiring, the cable-length and connector resistance between the CRMSQB and SIS-featured ALC is dynamically compensated (system damping factor 10.000), further reducing distortion, while increasing response accuracy.

The CRMSQB is available as CRMSQB, with CRMSQ width-matching and as CRMSQBsl, with CRMSQ depth-matching, with a 25,4cm / 210-in. system depth.

The post CRMSQB appeared first on Alcons Audio.

The front-loaded system delivers a super accurate bass and sub response with highest output under lowest distortion, due to the long-stroke 15” woofer. This new-generation transducer is fitted with a large, dual- 3.5” voice-coil Neodymium motor, enabling a significantly-extended excursion*, while maintaining a high sensitivity. Specific attention in this design has been paid to obtain lowest possible distortion. The Max-Vent™ port design combines further increased output with low power compression. *(not included in SPLpeak spec).

Optimal deployment flexibility is guaranteed: The LR15B can be used as single subwoofer or in multiples; As end-fire or cardioid array; Together with LR15 or in separate sub-only arrays. All functionality is possible in stacked or flown configurations. The integrated stand mount adapter provides for easy top/sub combinations with any Alcons pro-ribbon system.

Rated for a high WorkingLoadLimit with 1:10 safety ratio, the versatile rigging system, with front and rear splaying possibility, enables straight or pre-curved flown (cardioid) arrays, to be flown besides or behind an LR15 array.

Array configurations can be simulated through the LR15 GLL in the Alcons Ribbon Calculator (ARC), Alcons’ high-resolution 3D simulation program.

Mobile (cardioid) stacks of up to 3 units can be transported through the PRRGLR15B pre-rig, including stack-specific softcover.

For full system performance, the LR15B is to be driven and controlled by the ALC amplified loudspeaker controller; Driven by the ALC, the LR15B delivers full operation flexibility, maximum sound quality and output power with long-term operation reliability.

The Signal Integrity Sensing™ pre-wiring ensures complete cable/connector compensation between the LR15B and ALC, significantly increasing response accuracy and reducing both linear and non-linear distortion to an absolute minimum, regardless of cable length and system impedance.

The post LR15B appeared first on Alcons Audio.

By means of a front and rear located woofer configuration, in combination with dedicated processing, the system offers selectable cardioid low-frequency pattern control and excellent rear rejection (up to 42dB), without the need for additional cabinets.

On the front side, one 15” long-excursion woofer with 4-in. voice-coil with double-spider and demodulation ring, is mounted in a front-loaded configuration.

On the rear side, a single 12” long-excursion woofer with 4-in. voice-coil with double-spider, is mounted in a “front”-loaded configuration.

The large bass reflex ports on the front and the rear side enable excellent breathing capacity, increasing overall output while minimising port-compression.

The relatively low-weight, but rigid enclosure is finished in Durotect™ scratch-resistant coating and is fitted with 2 handles for easy logistics and an M20 stand mount flange (road-version).

The BC272 is powered and controlled by the ALC amplified loudspeaker controller. Driven by the ALC, the BC272 delivers maximum sound quality and output power with long-term operation reliability. Through the integrated processor, the ALC offers BC272-specific drive processing with response optimisation, dedicated power and excursion protection, and hybrid filtering.

The preset library contains cardioid settings for maximum rear-/side-ward attenuation.

The 4 ohms system impedance, makes for a very efficient amplifier loading; Thus enabling maximum output from a single, very compact configuration.

Through the SIS™ (Signal Integrity Sensing) circuit, the cable-length and connector resistance between the BC272 and ALC is completely compensated (system damping factor >10.000), for further increased accuracy and controlled cone-travel, resulting in a tighter sub and bass response.

The BC272 is available in road-version and installation (“i”) version, without handles, wheel dolly board and M20 threaded stand mount flange. It is finished in Durotect™ scratch-resistant coating; Through the Architect Color Option™ program, the BC272 can be finished in any RAL™ color.

The post BC272 appeared first on Alcons Audio.

Specific attention has been paid to obtain a linear response in the operating bandwidth, while handling ultra-low frequency transients with maximum control.

The 18” custom-designed woofer features a large motor structure with dual 3” voice-coils offering an extreme excursion of 30 mm / 1.2-in. resulting in a 10 dB more excursion capability than a traditional (pro) 18” woofer. (not included in SPLpeak spec).

The direct-radiating transducer mounted in the internally-stiffened, sealed cabinet enables an in-room response below 10 Hz; The superb impulse response is a perfect match with the ultra-fast transient response of the Alcons pro-ribbon systems. The 4 ohms impedance caters for maximum amplifier efficiency.

The ultra-slim enclosure design provides for stacking, flying or wall- and ceiling-mounting in even the smallest of spaces; For this, the cabinet is equipped with M10 mounting points.

For full system performance, the CRMS-LFE18sl is to be driven and controlled by the ALC amplified loudspeaker controller, to deliver the most accurate reproduction for even the lowest octaves, to bring the most realistic experience of speech, music and effects.
The integrated factory presets in the drive processor of the ALC offer optimisation settings, as well as VHIR™ processing for perfect phase-matching with an Alcons pro-ribbon system.

The Signal Integrity Sensing™ pre-wiring ensures complete cable/connector compensation between the CRMS-LFE18sl and ALC, significantly increasing response accuracy and reducing both linear and non-linear distortion to an absolute minimum, regardless of cable length and system impedance.

Typical applications include LFE system for quality-conscious post-production facilities and mastering suites, high-end mix/screening rooms, recording studios and premium home theatres.

The post CRMS-LFE18sl appeared first on Alcons Audio.

The direct-radiating woofer is mounted in a vented chamber, with large bass reflex port for excellent breathing capacity, increasing overall output while minimising port-compression.

The double baffle board and the combination of complex internal panel lay-out with extensive bracing brings a rigid structure with a high enclosure stiffness from a relatively low-weight package.

For full system performance, the BF121 is driven and controlled by the ALC amplified loudspeaker controller; Driven by the ALC, the BF121 delivers maximum sound quality and output power with long-term operation reliability. The integrated factory presets in the drive processor of the ALC offer gain, phase and filtering matching with all Alcons top systems, including cardioid projection control presets. The additional front-positioned NL4 connector caters for easy “reverse connection” in cardioid arrays.

The 4 ohms system impedance, makes for a very efficient amplifier loading; Thus enabling maximum output from a single, very compact configuration.

The BF121 is SIS™ pre-wired: Through the Signal Integrity Sensing circuit of the ALC, the cable-length and connector resistance between the BF121 and ALC is dynamically compensated (system damping factor 10.000), further reducing distortion, while increasing response accuracy.

The BF121 is available in road-version and installation (“i”) version, without handles, wheel dolly board and M20 threaded stand mount flange. It is finished in Durotect™ scratch-resistant coating; Through the Architect Color Option™ program, the BF121 can be finished in any RAL™ color.

The BF121 packs the same punch and accuracy as its bigger brothers BF151 and BF181 compact subwoofers, and is a perfect companion for the VR5 monitor as super-compact PA system.

The post BF121 appeared first on Alcons Audio.

Specific attention has been paid to obtain a linear response in the operating bandwidth, while handling ultra-low frequency transients with maximum control.

The 18” custom-designed woofer features a large motor structure with dual 3” voice-coils offering an extreme excursion of 30 mm / 1.2-in. resulting in a 10 dB more excursion capability than a traditional (pro) 18” woofer. (not included in SPLpeak spec).

The direct-radiating transducer mounted in the internally-stiffened, sealed cabinet enables an in-room response below 10 Hz; The superb impulse response is a perfect match with the ultra-fast transient response of the Alcons pro-ribbon systems. The 4 ohms impedance caters for maximum amplifier efficiency.

For full system performance, the CRMS-LFE18 is to be driven and controlled by the ALC amplified loudspeaker controller; Driven by the ALC, the CRMS-LFE18 delivers maximum sound quality and output power with long-term operation reliability.

The integrated factory presets in the drive processor of the ALC offer optimisation settings, as well as VHIR™ processing for perfect phase-matching with an Alcons pro-ribbon system.

The Signal Integrity Sensing™ pre-wiring ensures complete cable/connector compensation between the CRMS-LFE18 and ALC, significantly increasing response accuracy and reducing both linear and non-linear distortion to an absolute minimum, regardless of cable length and system impedance.

The combination of CRMS-LFE18 and ALC delivers the most accurate reproduction for even the lowest octaves, to bring the most realistic experience of speech, music and effects, as it was intended.

The CRMS-LFE18 is also available in a slim enclosure (“CRMS-LFE18sl”), for maximizing space-efficiency with the Alcons slim-sized main systems.

Typical applications include LFE system for quality-conscious post-production facilities and mastering suites, high-end mix/screening rooms, recording studios and premium home theatres.

The post CRMS-LFE18 appeared first on Alcons Audio.

The direct-radiating 21” extended excursion woofer with large, 4.5” voice-coil is mounted in an optimally vented chamber, with a large bass reflex port for excellent breathing capacity, increasing overall output while minimising port-compression. Specific attention has been paid to obtain a linear response in the operating bandwidth, while handling low frequency transients with maximum control.
The 4 ohms impedance offers maximum amplifier efficiency.

Although the CB211sl has a slightly lower sensitivity than the 18” version (due to the higher mass), it has around 6 dB more excursion capability, greatly increasing the excursion-limited output performance (not included in the mentioned specifications!).

The ultra-slim enclosure design provides for stacking, flying or wall-mounting; For this, the cabinet is equipped with M10 mounting points. The side-oriented reflex vent enables the cabinet to be closely mounted behind the screen without chance of screen resonance. The CB211sl is also available with front-venting for in-wall baffle mounting (“FV” version).

For full system performance, the CB211sl is to be driven and controlled by the ALC amplified loudspeaker controller; Driven by the ALC, the CB211sl delivers maximum sound quality and output power with long-term operation reliability. The integrated factory presets in the drive processor of the ALC offer gain, phase and filtering matching.

The Signal Integrity Sensing™ pre-wiring ensures complete cable/connector compensation between the CB211sl and the ALC amplified loudspeaker controller, significantly increasing response accuracy, regardless of cable length and system impedance. Especially with the cinema-typical long speaker cable runs and the subwoofer system’s possible low impedance, the effect is remarkable, resulting in really tight and accurate reproduction for even the lowest octaves.

Due to its form factor, the CB211sl is designed as low frequency extension in medium-to-large cinema systems, as well as Rear LFE subwoofer channel in large immersive surround systems.

The post CB211sl appeared first on Alcons Audio.